Circuit Bending Kit for Speak and Spell, Casio Keyboards and more - Circuit Bent

Description

Circuit Bending Kit / Electronic Components for Circuit Bending
Circuit Bending Kit / Electronic Components for Circuit Bending of Speak and Spell, Casio Keyboards and other electronics devices and toys.
VERY FAST SHIPPING - located in USA
This auction is for collection of hand picked electronic components that can be used for circuit bending.  I use these components in my circuit bent projects (see video demo). Auction is for electronic components shown in the photo ONLY, quarter is to show size/scale of components. No other items are included (
Speak and Spell, Casio Keyboard, etc. are NOT included
).
You will need an item to circuit bend, hookup wire, basic hand tools and basic soldering skills to use these components in your circuit bending project, these are also NOT included.  Various details of circuit bending diagrams and instructions can be found on the internet.
These components work especially well with the Speak and Spell, Speak and Math and Speak and Read as well as other circuit bendable electronics
Description of kit/components in auction:
Circuit bending components/kit.  Basic component kit to get started in circuit bending your favorite vintage toy or keyboard.  Great for Speak and Spell, Speak and Math, Speak and Read, Casio keyboards or other electronic toys/devices.
NOTE:
All mounting hardware is included on toggle/pushbutton switches, 1/4" jack, LED mount and body contact.  All components are new or NOS (New Old Stock)/surplus, no pulls.
1 - Linear Potentiometer
. Typically used for adjusting pitch up or down
NOTE:
The current potentiometer has solder lugs for easier wire hookup/soldering and varies slightly from the one on the photo.
2 - Small Trimmer Potentiometers  -
Typically used with pitch potentiometer allow full range of pitch knob without crashing circuit bent unit (prevents resistance from going to zero)
1 - Pitch Knob
, fits 1/4" shaft of included pitch potentiometer.
NOTE:
Pitch knob may vary from the one pictured. This knob may be New, NOS (New Old Stock) or Vintage depending on what I have in stock.
1 - Volume Potentiometer
. Typically used for adding volume control to Speak and Spell/other devices with no volume control or "voltage starving" bends and glitches.
1 - Volume Knob
, fits 1/4" shaft of included volume potentiometer.
This knob may be New, NOS (New Old Stock) or Vintage depending on what I have in stock.
3 - Mini 2-position SPDT Toggle Switches (ON/ON or ON/OFF)
with Solder eyelet lugs. Typically used for setting/switching on "Glitches". Can set two separate glitches from each switch. Can have connections on each position.  (toggle switch may vary slightly in appearance from photo)
1 - Mini SPDT 3 position Toggle switch (ON/OFF/ON)
with Solder eyelet lugs. Typically used for locking in loops, glitches or turning pitch potentiometer On and Off (for interesting pitch effects - example - ON high pitch/OFF normal pitch/ON low pitch).
1 - Sub-Mini SPDT 2 position Toggle switch (ON/ON or ON/OFF)
with Solder eyelet lugs. Typically used with pushbutton (N.O. Red) to lock in loops
1 - Normally Open (N.O. Red) Momentary Pushbutton.
Typically used for sampling loops
1 - Normally Closed (N.C. Black) Momentary Pushbutton.
Typically used for reset button (interrupts power from batteries for hard reset)
1 - Body Contact.
Typically used to lower pitch by touching/tapping.  Used to create tremolo effect. NOTE: Can be brass or silver color, they work the same way.
3 - LEDs (Size T 3/4 / 5mm)  1 Green LED, 1 Red LED(not shown) , 1 Red/Green/Blue fading and color mixing
Typically used for power indicator light or beat/output signal follower (flash to the glitch and/or loop)
4 - Limiting Resistors for LEDs
Typically used limit input current to the LED.
1 - Chrome LED mount/holder for T 3/4 / 5mm LED.
Panel mount hardware for included LED (or your own LED)
1 - Light Sensitive CDS cell.
Typically used for varing pitch or volume with amount of light.  Can be used to create Theremin type effect.
1 - 1/4" Output Jack.
High Quality REAN (by Neutrik AG) Jack. with solder lugs. Typically used to accept a standard TRS type audio plug for your circuit bent device to run through an amp, effects processor or recording samples to your computer or Casio SK-1 :-) Can leave in speaker in bent device, can hook up jack so when plugged into external amp, internal speaker is disconnected.
2 - Alligator clips jumper wires -
Typically used to test bends before soldering or searching for new bends.
(Colors will vary)
1 - packet of reference material (not shown in photo)-
List, markings and descriptions of components, resistor chart (for 4-band and 5 band resistors) and capacitor chart with values and corresponding markings
PLUS
- A few extra items for experimenting
Below is an example video of some Speak and Spells and Speak and Maths I've circuit bent with some of the various electronic components in this auction.  This video is for demonstration purposes ONLY.  The Speak and Spell/Speak and Math/Speak and Spell are
NOT
included in the auction.
Circuit Bent Speak and Spell 1 - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
Circuit Bent Speak and Math - loops - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
Circuit Bent Speak and Read - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
New Circuit Bent Speak and Math by StressMyCircuits - loops & glitches plus RGB color cycling LED - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
Please check out my other auctions for more circuit bent electronics (Speak and Math, Speak and Read, Speak and Spell, Casio, etc.)  unbent electronics and related items. Thank you.
Please Visit My eBay Store! Stress My Circuits
Shipping and handling  via US Mail. Includes delivery confirmation . Shipping to Continental U.S. only.
Winning bidder must send payment within 5 days of end of auction. PayPal Only.
If you have any question please let me know, please ask questions before placing your bid and I'll be happy to answer them.
Payment method is PayPal.
Thanks for looking at my auction.
Pay me securely with any major credit card through PayPal!